Models / Small-parts drawer stack

Small-parts drawer stack

Drawer stack: a finger-jointed cabinet with separate sliding tray drawers. Drawer count and clearances generate the shelf levels and outer height. Assembly: glue the carcass and shelf tabs, then glue each drawer square. Sand the runners and test the slide clearance before applying a finish.

22 parts on 2 sheets, shown together. Each sheet has its own cut file.

Source 58 lines

// Drawer stack: a finger-jointed cabinet with separate sliding tray drawers.
// Drawer count and clearances generate the shelf levels and outer height.
// Assembly: glue the carcass and shelf tabs, then glue each drawer square.
// Sand the runners and test the slide clearance before applying a finish.
 
use <kerf/tabs>
 
/* [Cabinet] */
width = 190; // [120:5:300]
depth = 140; // [90:5:240]
drawers = 3; // [1:1:5]
drawer_height = 32; // [25:1:65]
slide_ease = 1.2; // [0.6:0.1:2]
 
/* [Assembled view] */
// Keep at least 40 percent of each drawer supported inside the carcass.
extension = 0; // [0:0.05:0.6]
 
/* [Material] */
$thickness = 3; // [2:0.5:6]
$kerf = 0.15; // [0:0.01:0.3]
clearance = 0.15; // [0:0.05:0.4]
 
/* [Hidden] */
$material = "plywood";
t = $thickness;
step = drawer_height + 2 * slide_ease + t;
height = drawers * step + t;
span = width - 2 * t;
reach = depth - t;
dw = span - 2 * slide_ease;
dd = reach - 4;
assert(extension >= 0 && extension <= 0.6, "Keep at least 40 percent of the drawer supported");
assert(drawer_height > 3 * t + 8, "Drawer is too shallow for this sheet thickness");
step("Glue up the carcass, with the runner shelves in the side slots") {
  part("Carcass floor", at = [0, 0, 0]) finger_rect([width, depth], ["flat", "out", "out", "out"]);
  part("Carcass top", at = [0, 0, height - t]) finger_rect([width, depth], ["flat", "out", "out", "out"]);
  part("Carcass back", at = [0, depth, 0], rotate = [90, 0, 0]) finger_rect([width, height], ["in", "out", "in", "out"]);
  part("Carcass side", qty = 2, at = [[0, 0, 0], [width - t, 0, 0]], rotate = [90, 0, 90]) difference() {
    finger_rect([depth, height], ["in", "in", "in", "flat"]);
    if (drawers > 1) for (i = [1:drawers - 1]) translate([0, i * step + t / 2]) slots(reach, clearance = clearance);
  }
  if (drawers > 1) part("Runner shelf", qty = drawers - 1, at = [for (i = [1:drawers - 1]) [t, 0, i * step]])
    tab_rect([span, reach], [false, true, false, true]);
}
step("Glue up each drawer and slide it in")
  for (i = [0:drawers - 1]) {
    x = t + slide_ease;
    y = 2 - extension * dd;
    z = t + slide_ease + i * step;
    part(str("Drawer ", i + 1, " floor"), at = [x, y, z]) finger_rect([dw, dd], "out");
    part(str("Drawer ", i + 1, " front"), at = [x, y + t, z], rotate = [90, 0, 0]) difference() {
      finger_rect([dw, drawer_height], ["in", "out", "flat", "out"]);
      translate([dw / 2, drawer_height]) circle(d = min(24, drawer_height - 2 * t - 4));
    }
    part(str("Drawer ", i + 1, " back"), at = [x, y + dd, z], rotate = [90, 0, 0]) finger_rect([dw, drawer_height], ["in", "out", "flat", "out"]);
    part(str("Drawer ", i + 1, " side"), qty = 2, at = [[x, y, z], [x + dw - t, y, z]], rotate = [90, 0, 90]) finger_rect([dd, drawer_height], ["in", "in", "flat", "in"]);
  }