// Drawer stack: a finger-jointed cabinet with separate sliding tray drawers. // Drawer count and clearances generate the shelf levels and outer height. // Assembly: glue the carcass and shelf tabs, then glue each drawer square. // Sand the runners and test the slide clearance before applying a finish. use /* [Cabinet] */ width = 190; // [120:5:300] depth = 140; // [90:5:240] drawers = 3; // [1:1:5] drawer_height = 32; // [25:1:65] slide_ease = 1.2; // [0.6:0.1:2] /* [Assembled view] */ // Keep at least 40 percent of each drawer supported inside the carcass. extension = 0; // [0:0.05:0.6] /* [Material] */ $thickness = 3; // [2:0.5:6] $kerf = 0.15; // [0:0.01:0.3] clearance = 0.15; // [0:0.05:0.4] /* [Hidden] */ $material = "plywood"; t = $thickness; step = drawer_height + 2 * slide_ease + t; height = drawers * step + t; span = width - 2 * t; reach = depth - t; dw = span - 2 * slide_ease; dd = reach - 4; assert(extension >= 0 && extension <= 0.6, "Keep at least 40 percent of the drawer supported"); assert(drawer_height > 3 * t + 8, "Drawer is too shallow for this sheet thickness"); step("Glue up the carcass, with the runner shelves in the side slots") { part("Carcass floor", at = [0, 0, 0]) finger_rect([width, depth], ["flat", "out", "out", "out"]); part("Carcass top", at = [0, 0, height - t]) finger_rect([width, depth], ["flat", "out", "out", "out"]); part("Carcass back", at = [0, depth, 0], rotate = [90, 0, 0]) finger_rect([width, height], ["in", "out", "in", "out"]); part("Carcass side", qty = 2, at = [[0, 0, 0], [width - t, 0, 0]], rotate = [90, 0, 90]) difference() { finger_rect([depth, height], ["in", "in", "in", "flat"]); if (drawers > 1) for (i = [1:drawers - 1]) translate([0, i * step + t / 2]) slots(reach, clearance = clearance); } if (drawers > 1) part("Runner shelf", qty = drawers - 1, at = [for (i = [1:drawers - 1]) [t, 0, i * step]]) tab_rect([span, reach], [false, true, false, true]); } step("Glue up each drawer and slide it in") for (i = [0:drawers - 1]) { x = t + slide_ease; y = 2 - extension * dd; z = t + slide_ease + i * step; part(str("Drawer ", i + 1, " floor"), at = [x, y, z]) finger_rect([dw, dd], "out"); part(str("Drawer ", i + 1, " front"), at = [x, y + t, z], rotate = [90, 0, 0]) difference() { finger_rect([dw, drawer_height], ["in", "out", "flat", "out"]); translate([dw / 2, drawer_height]) circle(d = min(24, drawer_height - 2 * t - 4)); } part(str("Drawer ", i + 1, " back"), at = [x, y + dd, z], rotate = [90, 0, 0]) finger_rect([dw, drawer_height], ["in", "out", "flat", "out"]); part(str("Drawer ", i + 1, " side"), qty = 2, at = [[x, y, z], [x + dw - t, y, z]], rotate = [90, 0, 90]) finger_rect([dd, drawer_height], ["in", "in", "flat", "in"]); }