Models / Cantilever sewing and tool case
Cantilever sewing and tool case
Cantilever case: two banks of trays rise outward on parallel pivot links. The pivot offsets and link lengths are computed from the tray dimensions. Assembly: glue the base and each tray square. Bolt the links outside the front and back walls, using washers and standoffs to separate link layers. Link pivots must turn freely. Do not glue the links to the trays.
41 parts on 2 sheets, shown together. Each sheet has its own cut file.
Source
// Cantilever case: two banks of trays rise outward on parallel pivot links.
// The pivot offsets and link lengths are computed from the tray dimensions.
// Assembly: glue the base and each tray square. Bolt the links outside the
// front and back walls, using washers and standoffs to separate link layers.
// Link pivots must turn freely. Do not glue the links to the trays.
/* [Storage] */
tray_width = 110; // [90:5:170]
depth = 140; // [100:5:220]
tray_height = 32; // [25:1:50]
base_height = 44; // [35:1:75]
levels = 2; // [1:1:3]
lids = false;
/* [Assembled view] */
// Zero closes the trays; one raises them to the designed open position.
opening = 0.8; // [0:0.05:1]
/* [Material] */
$thickness = 3; // [2:0.5:6]
$kerf = 0.15; // [0:0.01:0.3]
pin_diameter = 3; // [3:0.5:4]
pivot_clearance = 0.3; // [0.2:0.05:0.6]
washer_gap = 0.5; // [0.3:0.1:1]
/* [Hidden] */
$material = "plywood";
t = $thickness;
seam = 6;
base_w = 2 * tray_width + seam;
step = tray_height + 3;
offset = tray_width * 0.46;
spread = tray_width * 0.24;
margin = tray_width * 0.10;
link_length = sqrt(offset * offset + step * step);
closed_angle = atan2(step, offset);
angle = closed_angle + (82 - closed_angle) * opening;
dx = offset - link_length * cos(angle);
dz = link_length * sin(angle);
arm_width = max(9, 2 * t + 3);
assert(spread * sin(closed_angle) > arm_width + 0.5, "Increase tray height or width, or use thinner stock, to separate the parallel links");
assert(base_height - tray_height / 2 > t + pin_diameter + 3, "Increase the base height to support its pivot holes");
assert(tray_height / 2 > t + pin_diameter + 2, "Increase tray height for this sheet and pivot size");
assert(margin > pin_diameter / 2 + 3, "Pivot margin is too small");
function anchor(side, k, upper = false) = margin + k * spread + ((side > 0 ? !upper : upper) ? offset : 0);
function tray_at(side, j) = [(side < 0 ? 0 : tray_width + seam) + side * j * dx, 0,
base_height - tray_height / 2 + j * dz - tray_height / 2];
function pivot(side, j, k, upper = false) = tray_at(side, j) + [anchor(side, k, upper), 0, tray_height / 2];
module pivot_holes(side, base = false, stage = 0) {
// Base walls support outgoing links only; top trays receive incoming links.
// Intermediate trays connect both stages.
for (k = [0:1], upper = base ? [false] : (stage == levels ? [true] : [false, true]))
translate([anchor(side, k, upper), base ? base_height - tray_height / 2 : tray_height / 2]) circle(d = pin_diameter + pivot_clearance);
}
module tray(name, w, h, at, side = 0, stage = 0) {
part(str(name, " floor"), at = at) finger_rect([w, depth], "out");
for (back = [false, true]) part(str(name, back ? " back" : " front"), at = at + [0, back ? depth : t, 0], rotate = [90, 0, 0]) difference() {
finger_rect([w, h], ["in", "out", "flat", "out"]);
if (side == 0) for (s = [-1, 1]) translate([s < 0 ? 0 : tray_width + seam, 0]) pivot_holes(s, true);
else pivot_holes(side, stage = stage);
}
part(str(name, " end"), qty = 2, at = [at, at + [w - t, 0, 0]], rotate = [90, 0, 90]) finger_rect([depth, h], ["in", "in", "flat", "in"]);
}
module link() difference() {
hull() { circle(d = arm_width); translate([link_length, 0]) circle(d = arm_width); }
for (x = [0, link_length]) translate([x, 0]) circle(d = pin_diameter + pivot_clearance);
}
step("Glue up the base well") tray("Base well", base_w, base_height, [0, 0, 0]);
for (side = [-1, 1], j = [1:levels]) {
tag = str(side < 0 ? "Left" : "Right", " tray ", j);
step(str("Glue up the level ", j, " trays and bolt their links on outside the front and back walls")) {
tray(tag, tray_width, tray_height, tray_at(side, j), side, j);
for (back = [false, true], k = [0:1]) {
y = back ? depth + washer_gap + t + (j - 1) * (t + washer_gap) : -washer_gap - (j - 1) * (t + washer_gap);
part(str(side < 0 ? "Left" : "Right", " link ", j, back ? " back " : " front ", k + 1),
at = pivot(side, j - 1, k) + [0, y, 0], rotate = [90, -(side < 0 ? angle : 180 - angle), 0]) link();
}
}
if (lids && j == levels) step("Glue a locator under each lid and set the lids on the top trays") {
at = tray_at(side, j);
part(str(tag, " lid"), at = at + [-2, -2, tray_height]) rect([tray_width + 4, depth + 4], r = 3);
part(str(tag, " lid locator"), at = at + [t + 0.7, t + 0.7, tray_height - t]) rect([tray_width - 2 * t - 1.4, depth - 2 * t - 1.4], r = 2);
}
}