// Cantilever case: two banks of trays rise outward on parallel pivot links. // The pivot offsets and link lengths are computed from the tray dimensions. // Assembly: glue the base and each tray square. Bolt the links outside the // front and back walls, using washers and standoffs to separate link layers. // Link pivots must turn freely. Do not glue the links to the trays. /* [Storage] */ tray_width = 110; // [90:5:170] depth = 140; // [100:5:220] tray_height = 32; // [25:1:50] base_height = 44; // [35:1:75] levels = 2; // [1:1:3] lids = false; /* [Assembled view] */ // Zero closes the trays; one raises them to the designed open position. opening = 0.8; // [0:0.05:1] /* [Material] */ $thickness = 3; // [2:0.5:6] $kerf = 0.15; // [0:0.01:0.3] pin_diameter = 3; // [3:0.5:4] pivot_clearance = 0.3; // [0.2:0.05:0.6] washer_gap = 0.5; // [0.3:0.1:1] /* [Hidden] */ $material = "plywood"; t = $thickness; seam = 6; base_w = 2 * tray_width + seam; step = tray_height + 3; offset = tray_width * 0.46; spread = tray_width * 0.24; margin = tray_width * 0.10; link_length = sqrt(offset * offset + step * step); closed_angle = atan2(step, offset); angle = closed_angle + (82 - closed_angle) * opening; dx = offset - link_length * cos(angle); dz = link_length * sin(angle); arm_width = max(9, 2 * t + 3); assert(spread * sin(closed_angle) > arm_width + 0.5, "Increase tray height or width, or use thinner stock, to separate the parallel links"); assert(base_height - tray_height / 2 > t + pin_diameter + 3, "Increase the base height to support its pivot holes"); assert(tray_height / 2 > t + pin_diameter + 2, "Increase tray height for this sheet and pivot size"); assert(margin > pin_diameter / 2 + 3, "Pivot margin is too small"); function anchor(side, k, upper = false) = margin + k * spread + ((side > 0 ? !upper : upper) ? offset : 0); function tray_at(side, j) = [(side < 0 ? 0 : tray_width + seam) + side * j * dx, 0, base_height - tray_height / 2 + j * dz - tray_height / 2]; function pivot(side, j, k, upper = false) = tray_at(side, j) + [anchor(side, k, upper), 0, tray_height / 2]; module pivot_holes(side, base = false, stage = 0) { // Base walls support outgoing links only; top trays receive incoming links. // Intermediate trays connect both stages. for (k = [0:1], upper = base ? [false] : (stage == levels ? [true] : [false, true])) translate([anchor(side, k, upper), base ? base_height - tray_height / 2 : tray_height / 2]) circle(d = pin_diameter + pivot_clearance); } module tray(name, w, h, at, side = 0, stage = 0) { part(str(name, " floor"), at = at) finger_rect([w, depth], "out"); for (back = [false, true]) part(str(name, back ? " back" : " front"), at = at + [0, back ? depth : t, 0], rotate = [90, 0, 0]) difference() { finger_rect([w, h], ["in", "out", "flat", "out"]); if (side == 0) for (s = [-1, 1]) translate([s < 0 ? 0 : tray_width + seam, 0]) pivot_holes(s, true); else pivot_holes(side, stage = stage); } part(str(name, " end"), qty = 2, at = [at, at + [w - t, 0, 0]], rotate = [90, 0, 90]) finger_rect([depth, h], ["in", "in", "flat", "in"]); } module link() difference() { hull() { circle(d = arm_width); translate([link_length, 0]) circle(d = arm_width); } for (x = [0, link_length]) translate([x, 0]) circle(d = pin_diameter + pivot_clearance); } step("Glue up the base well") tray("Base well", base_w, base_height, [0, 0, 0]); for (side = [-1, 1], j = [1:levels]) { tag = str(side < 0 ? "Left" : "Right", " tray ", j); step(str("Glue up the level ", j, " trays and bolt their links on outside the front and back walls")) { tray(tag, tray_width, tray_height, tray_at(side, j), side, j); for (back = [false, true], k = [0:1]) { y = back ? depth + washer_gap + t + (j - 1) * (t + washer_gap) : -washer_gap - (j - 1) * (t + washer_gap); part(str(side < 0 ? "Left" : "Right", " link ", j, back ? " back " : " front ", k + 1), at = pivot(side, j - 1, k) + [0, y, 0], rotate = [90, -(side < 0 ? angle : 180 - angle), 0]) link(); } } if (lids && j == levels) step("Glue a locator under each lid and set the lids on the top trays") { at = tray_at(side, j); part(str(tag, " lid"), at = at + [-2, -2, tray_height]) rect([tray_width + 4, depth + 4], r = 3); part(str(tag, " lid locator"), at = at + [t + 0.7, t + 0.7, tray_height - t]) rect([tray_width - 2 * t - 1.4, depth - 2 * t - 1.4], r = 2); } }