Models / Articulated cable chain
Articulated cable chain
Cable chain: alternating wide and narrow U-links pivot on bought side bolts. Each link has two cheeks and one tabbed floor bridge. The channel stays open. Assembly: glue each U-link square, then connect adjacent cheeks with short bolts, washers and locknuts. Keep the pivots loose enough to turn freely. This free-pivot prototype has no mechanical bend stops or machine rating.
Download size: 563.5 × 66.5 mm. 24 parts on 1 sheet.
Source
// Cable chain: alternating wide and narrow U-links pivot on bought side bolts.
// Each link has two cheeks and one tabbed floor bridge. The channel stays open.
// Assembly: glue each U-link square, then connect adjacent cheeks with short
// bolts, washers and locknuts. Keep the pivots loose enough to turn freely.
// This free-pivot prototype has no mechanical bend stops or machine rating.
use <kerf/tabs>
/* [Chain] */
links = 8; // [3:1:14]
channel_width = 28; // [18:1:60]
link_height = 22; // [20:1:40]
pitch = 36; // [32:1:65]
pin_diameter = 3; // [3:0.5:5]
/* [Assembled view] */
// Angle between successive links; this does not add a physical stop.
joint_angle = 8; // [0:1:12]
/* [Material] */
$thickness = 3; // [2:0.5:6]
$kerf = 0.15; // [0:0.01:0.3]
clearance = 0.15; // [0:0.05:0.4]
pivot_clearance = 0.3; // [0.2:0.05:0.6]
axial_gap = 0.5; // [0.3:0.1:1]
/* [Hidden] */
$material = "plywood";
t = $thickness;
r = link_height / 2;
bridge_length = pitch - 2 * (r + 2);
floor_z = -r + 3;
assert(bridge_length >= 8, "Increase pitch or reduce link height");
assert(link_height > 2 * t + 10, "Increase link height for this thickness");
assert(pin_diameter + pivot_clearance < link_height - 10, "Pivot holes leave too little material");
assert((links - 1) * joint_angle <= 150, "Reduce bend or link count to avoid curling back");
function joint(i) = [i == 0 ? 0 : sum([for (j = [0:i - 1]) pitch * cos(j * joint_angle)]), 0,
r + (i == 0 ? 0 : sum([for (j = [0:i - 1]) pitch * sin(j * joint_angle)]))];
function direction(a) = [cos(a), 0, sin(a)];
function normal(a) = [-sin(a), 0, cos(a)];
module cheek() difference() {
hull() { circle(r = r); translate([pitch, 0]) circle(r = r); }
for (x = [0, pitch]) translate([x, 0]) circle(d = pin_diameter + pivot_clearance);
translate([pitch / 2, floor_z + t / 2]) rect([bridge_length / 2 + clearance, t + clearance], center = true);
}
for (i = [0:links - 1]) {
a = i * joint_angle;
span = channel_width + (i % 2 == 0 ? 0 : 2 * (t + axial_gap));
for (side = [-1, 1]) part(str("Link ", i + 1, side < 0 ? " left cheek" : " right cheek"),
at = joint(i) + [0, side * (span / 2 + t / 2) + t / 2, 0], rotate = [90, -a, 0]) cheek();
part(str("Link ", i + 1, " bridge"),
at = joint(i) + direction(a) * (pitch / 2 + bridge_length / 2) + normal(a) * floor_z + [0, -span / 2, 0], rotate = [-a, 0, 90])
tab_rect([span, bridge_length], [false, true, false, true], count = 1, width = bridge_length / 2);
}