Models / Bottle display tote
Bottle display tote
Bottle tote: a compartment tray with a tall central handle partition. Bottle diameter and column count generate the footprint and handle span. Assembly: glue all joints and the handle partition to the floor. Use for light display bottles until the chosen material and joints are load tested.
Download size: 486.5 × 324.5 mm. 7 parts on 1 sheet.
Source
// Bottle tote: a compartment tray with a tall central handle partition.
// Bottle diameter and column count generate the footprint and handle span.
// Assembly: glue all joints and the handle partition to the floor. Use for
// light display bottles until the chosen material and joints are load tested.
use <kerf/dividers>
/* [Bottles] */
bottle_diameter = 65; // [45:1:90]
columns = 2; // [2:1:4]
ease = 4; // [2:1:8]
wall_height = 65; // [45:5:100]
handle_height = 185; // [140:5:240]
/* [Material] */
$thickness = 4; // [3:0.5:6]
$kerf = 0.15; // [0:0.01:0.3]
clearance = 0.15; // [0:0.05:0.4]
/* [Hidden] */
$material = "plywood";
t = $thickness;
pitch = bottle_diameter + 2 * ease + t;
w = columns * pitch + t;
d = 2 * pitch + t;
inner = w - 2 * t;
slot_h = wall_height - t - 3;
assert(handle_height > wall_height + 55, "Handle needs room above the compartments");
part("Floor", at = [0, 0, 0]) difference() {
finger_rect([w, d], "out");
translate([t, d / 2]) slots_for_handle();
}
// Two short tabs locate the handle in the floor, avoiding its cross slots.
module slots_for_handle() {
for (x = [inner * 0.2, inner * 0.8]) translate([x, 0]) rect([14 + clearance, t + clearance], center = true);
}
step("Glue the long walls and end walls to the floor") {
part("Long wall", qty = 2, at = [[0, t, 0], [0, d, 0]], rotate = [90, 0, 0]) finger_rect([w, wall_height], ["in", "out", "flat", "out"]);
part("End wall", qty = 2, at = [[0, 0, 0], [w - t, 0, 0]], rotate = [90, 0, 90]) finger_rect([d, wall_height], ["in", "in", "flat", "in"]);
}
step("Stand the cross dividers on the floor and lower the handle partition over them, tabs into the floor") {
part("Handle partition", at = [t, d / 2 + t / 2, t], rotate = [90, 0, 0]) difference() {
union() {
rect([inner, handle_height], r = 8);
for (x = [inner * 0.2, inner * 0.8]) translate([x - 7, -t]) rect([14, t + 0.1]);
}
translate([inner / 2, handle_height - 25]) rect([min(95, inner - 30), 25], center = true, r = 10);
for (i = [1:columns - 1]) translate([i * pitch - t / 2 - (t + clearance) / 2, -1]) rect([t + clearance, slot_h / 2 + 1]);
}
part("Cross divider", qty = columns - 1, at = [for (i = [1:columns - 1]) [i * pitch, t + 0.5, t]], rotate = [90, 0, 90])
slotted_divider(d - 2 * t - 1, slot_h, [d / 2 - t - 0.5], "top", clearance);
}