// Weave: a pintograph, a drawing machine with two turning discs. The crank // turns a small drive gear that meshes with both discs; the right one has a // few more teeth than the left, so it slowly falls behind. An arm on a pin in // each disc carries the pencil where the two arms cross, and it draws loop // after loop, each a little different, weaving a cushion of lines. /* [Drawing] */ // Teeth on the right disc, against 60 on the left: fewer teeth make a finer weave and more crank turns right_teeth = 63; // [61:61 teeth / finest, 62:62 teeth / fine, 63:63 teeth / open, 64:64 teeth / widest] // Hole the left arm's pin goes in, as its distance from the disc centre left_pin = 40; // [16:16 mm, 24:24 mm, 32:32 mm, 40:40 mm] // Hole the right arm's pin goes in right_pin = 32; // [16:16 mm, 24:24 mm, 32:32 mm, 40:40 mm] // Arm length, pin to pencil: longer arms draw higher up the paper and flatter arm_length = 200; // [180:10:210] /* [Fit] */ // Total play between two meshing gears, at the pitch circle backlash = 0.4; // [0.3:0.05:0.6] // Added to the 6 mm holes that turn on brass bushes bearing_clearance = 0.3; // [0.2:0.05:0.4] /* [Assembly] */ // Crank angle in the assembled view; the discs turn more slowly, so it // goes past one turn crank_angle = 340; // [0:10:3600] /* [Export] */ // All parts, or one group at a time output = "all"; // [all:All parts, base:Base and feet, gears:Discs and drive gear, arms:Arms and pen sleeve, spacers:Spacers and handle, coupon:Fit test] /* [Material] */ // Sheet thickness $thickness = 3; // [2.8:0.1:3.2] // Beam width $kerf = 0.15; // [0:0.01:0.25] /* [Hidden] */ $material = "plywood"; $sheet = [600, 400]; $gap = 5; $fn = 96; t = $thickness; m = 2.5; z0 = 30; z1 = 60; z2 = right_teeth; L = arm_length; hole = 6 + bearing_clearance; // The discs turn on axles 190 mm apart; the drive gear sits below them, at // the pitch distance from both, so it moves a little with the tooth count s = 95; c1 = (z0 + z1) * m / 2; c2 = (z0 + z2) * m / 2; gx = (c1 * c1 - c2 * c2) / (4 * s); drive = [gx, -sqrt(c1 * c1 - (gx + s) * (gx + s))]; discs = [[-s, 0], [s, 0]]; holes = [16, 24, 32, 40]; // The handle stands on the drive gear, inside its teeth handle_r = 24; // A5 paper, landscape paper = [210, 148]; assert(contains([61, 62, 63, 64], z2), "Right disc: 61 to 64 teeth"); assert(contains(holes, left_pin), "Left pin: 16, 24, 32 or 40 mm"); assert(contains(holes, right_pin), "Right pin: 16, 24, 32 or 40 mm"); assert(L >= 180 && L <= 210, "Arm length: 180 to 210 mm"); assert(backlash >= 0.3 && backlash <= 0.6, "Backlash: 0.3 to 0.6 mm"); assert(bearing_clearance >= 0.2 && bearing_clearance <= 0.4, "Bearing clearance: 0.2 to 0.4 mm"); assert(t >= 2.8 && t <= 3.2, "Thickness: 2.8 to 3.2 mm"); assert($kerf >= 0 && $kerf <= 0.25, "Kerf: 0 to 0.25 mm"); assert(crank_angle >= 0 && crank_angle <= 3600, "Crank angle: 0 to 3600 degrees"); assert(contains(["all", "base", "gears", "arms", "spacers", "coupon"], output), "Unknown output"); function gcd(a, b) = b == 0 ? a : gcd(b, a % b); function polar(r, a) = [r * cos(a), r * sin(a)]; // The pins when the crank has turned a degrees: both discs turn the other // way, the left at z0 / z1 and the right at z0 / z2 of the crank's speed. // Both rows of holes point up at a = 0. function pins(a) = [discs[0] + polar(left_pin, 90 - a * z0 / z1), discs[1] + polar(right_pin, 90 - a * z0 / z2)]; // The pencil, where two circles of the arm length round the pins cross, // on the paper side function pen(a) = let (p = pins(a), v = p[1] - p[0], d = norm(v), h = sqrt(L * L - d * d / 4)) p[0] + v / 2 + [-v[1], v[0]] * h / d; // The drawing closes when the left disc has made z2 / gcd turns loops = z2 / gcd(z1, z2); turns = loops * z1 / z0; drawing = [for (i = [0:turns * 72]) pen(i * 5)]; xs = [for (p = drawing) p.x]; ys = [for (p = drawing) p.y]; // The arms always meet: the pins are at most this far apart, under 2 L reach = 2 * s + left_pin + right_pin; assert(reach < 2 * L - 60, "The arms must be long enough to meet"); // The angle between the arms at the pencil, widest and narrowest widest = 2 * asin(reach / 2 / L); narrowest = 2 * asin((2 * s - left_pin - right_pin) / 2 / L); // The paper sits as low as it can without going under the discs box = [max(xs) - min(xs), max(ys) - min(ys)]; paper_y = min(min(ys) - 8, max(88, (min(ys) + max(ys)) / 2 - paper[1] / 2)); assert(box[0] < paper[0] - 16 && max(ys) < paper_y + paper[1] - 8, "The drawing must fit on the paper"); // Base outline bx = 187.5; by0 = -116; by1 = ceil(paper_y + paper[1] + 10); // Involute teeth with a 20 degree pressure angle. backlash is shared between // the two gears of a mesh: every tooth is thinned by backlash / 2. The roots // get a plain radial relief. function gear_inv(a) = tan(a) * 180 / PI - a; function gear_polar(r, a) = [r * cos(a), r * sin(a)]; // Half the angular width of a tooth at radius r function gear_half(z, m, r, backlash) = let (rp = m * z / 2, rb = rp * cos(20), ar = acos(min(1, rb / r))) 90 / z + gear_inv(20) - gear_inv(ar) - backlash / (4 * rp) * 180 / PI; function gear_outline(z, m, backlash, steps = 12) = let (rp = m * z / 2, rb = rp * cos(20), lo = rp - 1.25 * m, hi = rp + m, start = max(lo, rb), hs = gear_half(z, m, start, backlash), ht = gear_half(z, m, hi, backlash)) [for (k = [0:z - 1]) each concat( [gear_polar(lo, 360 * k / z - hs)], [for (j = [(start > lo ? 0 : 1):steps]) let (r = start + (hi - start) * j / steps) gear_polar(r, 360 * k / z - gear_half(z, m, r, backlash))], [for (j = [1:4]) gear_polar(hi, 360 * k / z - ht + 2 * ht * j / 4)], [for (j = [steps - 1:-1:0]) let (r = start + (hi - start) * j / steps) gear_polar(r, 360 * k / z + gear_half(z, m, r, backlash))], [if (start > lo) gear_polar(lo, 360 * k / z + hs)], [for (j = [1:5]) gear_polar(lo, 360 * k / z + hs + (360 / z - 2 * hs) * j / 6)] )]; module externalgear(z) { polygon(gear_outline(z, m, backlash)); } // Timing, with the crank at 0: the drive gear has a tooth on +X. Seen along // the line between the axles, a tooth on one side of the drive gear faces a // space on the disc, so each disc's teeth are turned by rho to match. function rho(c, z) = let (a = atan2(c[1] - drive[1], c[0] - drive[0]), f = a * z0 / 360 - floor(a * z0 / 360)) a + 180 - (0.5 - f) * 360 / z; // n scored tally marks module tally(n, p) { score() for (j = [0:n - 1]) translate(p + [2 * j, 0]) rect([0.3, 4]); } module ring(od, id) { difference() { circle(d = od); circle(d = id); } } // A disc: the pin holes run up from the centre, numbered, and the one the // settings use is ringed module disc(z, c, pin, label) { difference() { rotate(rho(c, z)) externalgear(z); circle(d = hole); for (r = holes) translate([0, r]) circle(d = 4.4); } score() { for (r = holes) translate([5, r - 1.5]) text(str(r), size = 3); translate([0, pin]) outline() circle(d = 8.5); translate([0, -30]) text(label, size = 5, halign = "center"); translate([0, -38]) text(str(z, " TEETH"), size = 3.5, halign = "center"); } } module drive_gear() { difference() { externalgear(z0); circle(d = hole); translate([handle_r, 0]) circle(d = 4.4); } score() line([7, 0], [handle_r - 6, 0]); } // Pin hole at the origin, pencil hole at L along +X, and a short tail // beyond it so the arms cross at the pencil module arm() { difference() { hull() { circle(r = 8); translate([L, 0]) circle(r = 9); translate([L + 14, 0]) circle(r = 7); } circle(d = hole); translate([L, 0]) circle(d = 8.4); } score() translate([L / 2, 0]) text("WEAVE", size = 6, halign = "center", valign = "center"); score() for (x = [14, L - 15]) translate([x, 0]) rect([6, 0.3], center = true); } module base() { difference() { translate([-bx, by0]) rect([2 * bx, by1 - by0], r = 12); // M4 axle bolts for (c = concat(discs, [drive])) translate(c) circle(d = 4.4); } score() { // Where the paper goes, with the drawing's corners marked inside it translate([-paper[0] / 2, paper_y]) outline() rect(paper); for (p = [[min(xs), min(ys)], [max(xs), min(ys)], [min(xs), max(ys)], [max(xs), max(ys)]]) translate(p) { rect([6, 0.3], center = true); rect([0.3, 6], center = true); } translate([-146, by1 - 28]) text("WEAVE", size = 13, halign = "center"); // The whole drawing at a third of its size translate([-146, by1 - 52]) scale(1 / 3) translate([-(min(xs) + max(xs)) / 2, -(min(ys) + max(ys)) / 2]) polyline(drawing); translate([-146, by1 - 80]) text(str(z1, " : ", z2, " TEETH"), size = 4, halign = "center"); translate([-146, by1 - 87]) text(str("PINS ", left_pin, " / ", right_pin), size = 4, halign = "center"); translate([-146, by1 - 94]) text(str("ARMS ", L), size = 4, halign = "center"); translate([146, by1 - 28]) text("PINTOGRAPH", size = 6, halign = "center"); translate([146, by1 - 38]) text(str(turns, " TURNS TO CLOSE"), size = 4, halign = "center"); } } feet = [[-bx + 20, by0 + 20], [bx - 20, by0 + 20], [-bx + 20, by1 - 20], [bx - 20, by1 - 20]]; // The assembled view, base bottom at z = 0: gears on two axle spacers, the // nut on each crank pin, then the left arm on one pin spacer and the right // arm on two, crossing at the pencil a = crank_angle; P = pins(a); pencil = pen(a); zg = 4 * t; zn = 6 * t + 3.2; arm_z = [zn + t, zn + 2 * t]; function heading(p) = let (v = pencil - p) [0, 0, atan2(v[1], v[0])]; function at(p, z) = concat(p, [z]); if (output == "all" || output == "base") step("Glue up the base and the feet, with two spacers round each axle hole") { part("Base", qty = 2, at = [[0, 0, 0], [0, 0, t]]) base(); part("Foot", qty = 8, at = [for (f = feet, k = [0:1]) at(f, -2 * t + k * t)]) circle(d = 30); } if (output == "all" || output == "gears") step("Mesh the two discs and the drive gear on their axles") { // Both discs turn the other way from the crank, more slowly part("Left disc", qty = 2, at = [for (k = [0:1]) at(discs[0], zg + k * t)], rotate = [0, 0, -a * z0 / z1]) disc(z1, discs[0], left_pin, "LEFT"); part("Right disc", qty = 2, at = [for (k = [0:1]) at(discs[1], zg + k * t)], rotate = [0, 0, -a * z0 / z2]) disc(z2, discs[1], right_pin, "RIGHT"); part("Drive gear", qty = 2, at = [for (k = [0:1]) at(drive, zg + k * t)], rotate = [0, 0, a]) drive_gear(); } if (output == "all" || output == "arms") step("Bolt the arms on the crank pins and push the pencil through") { part("Arm", qty = 2, at = [at(P[0], arm_z[0]), at(P[1], arm_z[1])], rotate = [heading(P[0]), heading(P[1])]) arm(); // Under the left arm, down to the paper part("Pen sleeve", qty = 3, at = [for (k = [3:-1:1]) at(pencil, arm_z[0] - k * t)]) ring(16, 8.4); } if (output == "all" || output == "spacers") { step("Glue up the base and the feet, with two spacers round each axle hole") part("Axle spacer", qty = 6, at = [for (c = concat(discs, [drive]), k = [0:1]) at(c, 2 * t + k * t)]) ring(16, hole); step("Bolt the arms on the crank pins and push the pencil through") part("Pin spacer", qty = 3, at = [at(P[0], zn), at(P[1], zn), at(P[1], zn + t)]) ring(14, hole); step("Bolt the handle stack on the drive gear") part("Handle", qty = 5, at = [for (k = [0:4]) at(drive + polar(handle_r, a), 6 * t + 4 + k * t)]) ring(18, hole); } // The fit test lies on the table beside the base if (output == "all" || output == "coupon") part("Fit test", at = [bx + 20, by0, -2 * t]) { difference() { rect([130, 45], r = 3); for (i = [0:3]) translate([15 + 25 * i, 15]) circle(d = 6.1 + 0.1 * i); translate([113, 15]) circle(d = 8.4); translate([113, 34]) circle(d = 4.4); } for (i = [0:3]) tally(i + 1, [12 + 25 * i, 29]); } echo(str("Weave: the drawing closes after ", turns, " crank turns (", loops, " loops), ", round(box[0]), " x ", round(box[1]), " mm, on A5 paper ", round(paper_y), " mm above the disc axles; the arms meet at ", round(narrowest), " to ", round(widest), " degrees")); // Assembly, with base bottom at z = 0: glue the two plies of the base, each // disc and the drive gear, then the feet in pairs under the corners and two // axle spacers round each axle hole. Each axle is an M4 bolt up from below // with a 6 mm brass bush over it standing on the base; the gear turns on the // bush, clamped from above by a washer and nut. Mesh the gears with both rows // of holes pointing at the paper. Each crank pin is an M4 bolt up through the // ringed hole, nutted on the disc, with a brass bush: the left arm on one pin // spacer, the right arm on two, each under a washer and nut. Glue the three // pen sleeves under the left arm's pencil hole, lay the right arm on top and // push a pencil down through both until it rests on the paper. Bolt the // handle stack on a bush on the drive gear and tape A5 paper in its outline.