// Sector stand: a tilting deck on two trunnions, locked through curved slots. // Glue the fixed cheeks into the foot, and the moving flanges and front lip // into the deck. Bolt each flange to its cheek at the pivot and arc slot. // Loosen both arc bolts before adjusting, then tighten them again. use /* [Stand] */ width = 180; // [130:5:260] depth = 130; // [110:5:190] base_depth = 190; // [165:5:250] pivot_height = 65; // [55:5:90] radius = 78; // [65:1:100] angle = 35; // [10:1:65] lip_height = 18; // [14:1:25] /* [Material] */ $thickness = 3; // [2:0.5:6] $kerf = 0.15; // [0:0.01:0.3] clearance = 0.15; // [0:0.05:0.4] bolt_diameter = 4; // [3:0.5:5] washer_gap = 0.6; // [0.3:0.1:1] /* [Hidden] */ $material = "plywood"; t = $thickness; py = 25; v = 10; assert(angle >= 10 && angle <= 65, "Keep the deck within the arc-slot limits"); assert(radius < depth - 20, "Keep the clamp pivot inside the flange"); assert(base_depth > py + radius + 18, "Lengthen the foot under the arc cheeks"); assert(pivot_height > 2 * t + 24, "Raise the deck above the foot"); function arc(a, r = radius) = [py + r * cos(a), pivot_height - t + r * sin(a)]; function moving(u, z = 0) = [0, py + u * cos(angle) - z * sin(angle), pivot_height + u * sin(angle) + z * cos(angle)]; function fixed_x(s) = s < 0 ? -width / 2 - washer_gap - t : width / 2 + washer_gap; function flange_x(s) = s < 0 ? -width / 2 + 4 : width / 2 - 4 - t; step("Glue the fixed cheeks into the foot") { // The foot cuts the slots for the cheeks' tabs part("Foot", at = [0, 0, 0], slots = ["Left fixed sector", "Right fixed sector"], clearance = clearance) translate([-(width + 4 * t + 12) / 2, 0]) rect([width + 4 * t + 12, base_depth], r = 5); for (s = [-1, 1]) part(str(s < 0 ? "Left" : "Right", " fixed sector"), at = [fixed_x(s), 0, t], rotate = [90, 0, 90]) difference() { union() { hull() { rect([base_depth, 10]); for (a = [0:5:75]) translate(arc(a, radius + 12)) circle(r = 1); translate([py, pivot_height - t]) circle(r = 12); } for (y = [40, base_depth - 40]) translate([y - 10, -t]) rect([20, t]); } translate([py, pivot_height - t]) circle(d = bolt_diameter + 0.3); union() { polygon(concat([for (a = [10:1:65]) arc(a, radius + (bolt_diameter + 0.5) / 2)], [for (a = [65:-1:10]) arc(a, radius - (bolt_diameter + 0.5) / 2)])); for (a = [10, 65]) translate(arc(a)) circle(d = bolt_diameter + 0.5); } } } step("Glue the moving flanges and the front lip into the deck") { for (s = [-1, 1]) part(str(s < 0 ? "Left" : "Right", " moving flange"), at = [flange_x(s), py, pivot_height], rotate = [90, -angle, 90]) difference() { union() { hull() { circle(r = 10); translate([depth - 5, 0]) rect([10, 20], center = true); } for (u = [depth / 4, 3 * depth / 4]) translate([u - 6, v]) rect([12, t]); } for (u = [0, radius]) translate([u, 0]) circle(d = bolt_diameter + 0.3); } // The deck cuts the slots for the flanges' tabs, at the deck's angle part("Tilting deck", at = moving(0, v) + [-width / 2, 0, 0], rotate = [angle, 0, 0], slots = ["Left moving flange", "Right moving flange"], clearance = clearance) finger_rect([width, depth], ["out", "flat", "flat", "flat"]); part("Front lip", at = moving(t, v) + [-width / 2, 0, 0], rotate = [90 + angle, 0, 0]) finger_rect([width, lip_height], ["in", "flat", "flat", "flat"]); } step("Bolt each flange to its cheek at the pivot and through the arc slot") for (s = [-1, 1], u = [0, radius]) let (p = moving(u), lo = min(fixed_x(s), flange_x(s)) - 1, hi = max(fixed_x(s), flange_x(s)) + t + 1) hardware("steel", [lo, p[1], p[2]], [hi, p[1], p[2]], bolt_diameter, label = u == 0 ? "pivot bolt" : "clamp bolt");