// Screw press: laminated platens and hand knobs with captive hex nuts. // Clamp the lower platen onto four threaded rods using washers and nuts. // Glue the knob laminations around measured hex nuts without gluing the // threads. Put washers beneath the knobs and turn them evenly to press. // A small craft press for paper and light glue-ups, not for heavy pressing. /* [Platens] */ width = 180; // [140:5:260] depth = 140; // [110:5:200] platen_layers = 3; // [2:1:5] margin = 20; // [17:1:28] rod_height = 120; // [90:5:180] opening = 50; // [15:1:90] /* [Measured hardware] */ rod_diameter = 6; // [4:1:8] thread_pitch = 1; // [0.7:0.05:1.5] nut_flats = 10; // [7:0.5:14] nut_height = 5; // [3:0.5:7] nut_clearance = 0.25; // [0.1:0.05:0.5] washer_height = 1; // [0.5:0.5:2] /* [Material] */ $thickness = 3; // [2:0.5:6] $kerf = 0.15; // [0:0.01:0.3] /* [Hidden] */ $material = "plywood"; t = $thickness; ph = platen_layers * t; middle = ceil(nut_height / t); kh = (middle + 2) * t; top = ph + opening; turn = -360 * opening / thread_pitch; corners = [for (x = [margin, width - margin], y = [margin, depth - margin]) [x, y]]; assert(opening >= 15 && thread_pitch > 0, "Use a positive thread pitch and leave room above the base nuts"); assert(2 * ph + opening + washer_height + kh + 3 < rod_height, "Use longer rods or reduce the opening"); assert(margin > 15, "Keep knobs inside the platen edge"); assert(nut_flats > rod_diameter + 2 && nut_flats < 18, "Measure a suitable hex nut"); assert(width - 2 * margin > 40 && depth - 2 * margin > 35, "Leave a useful pressing area between rods"); module platen() difference() { rect([width, depth], r = 7); for (p = corners) translate(p) circle(d = rod_diameter + 0.6); } module knob() union() { circle(r = 11); for (a = [0:60:300]) translate([10 * cos(a), 10 * sin(a)]) circle(r = 4); } step("Glue up the lower platen and clamp it onto the four rods with nuts") { part("Lower platen lamination", stack = platen_layers, at = [0, 0, 0]) platen(); for (p = corners) { hardware("steel", [p[0], p[1], -nut_height], [p[0], p[1], rod_height], rod_diameter, label = "threaded rod"); for (z = [-nut_height, ph]) hardware("steel", [p[0], p[1], z], [p[0], p[1], z + nut_height], nut_flats / cos(30), sides = 6, label = "hex nut"); } } step("Glue up the upper platen and drop it over the rods") part("Upper platen lamination", stack = platen_layers, at = [0, 0, top]) platen(); step("Glue each knob's layers round a hex nut, without glue on the thread, and screw them down on washers") for (k = [0:3]) { p = corners[k]; z = top + ph + washer_height; part(str("Knob ", k + 1, " cover"), qty = 2, at = [[p[0], p[1], z], [p[0], p[1], z + (middle + 1) * t]], rotate = [0, 0, turn]) difference() { knob(); circle(d = rod_diameter + 0.6); } part(str("Knob ", k + 1, " nut pocket"), stack = middle, at = [p[0], p[1], z + t], rotate = [0, 0, turn]) difference() { knob(); circle(d = (nut_flats + nut_clearance) / cos(30), $fn = 6); } }