> Canonical HTML: https://kerfscript.mylasertools.com/models/screw-press/

# Laminated screw press

Screw press: laminated platens and hand knobs with captive hex nuts. Clamp the lower platen onto four threaded rods using washers and nuts. Glue the knob laminations around measured hex nuts without gluing the threads. Put washers beneath the knobs and turn them evenly to press. A small craft press for paper and light glue-ups, not for heavy pressing.

This design has 22 parts on 1 sheet. Customize it in the [playground](https://kerfscript.mylasertools.com/playground/?model=screw-press).

## Downloads

- [KerfScript source](https://kerfscript.mylasertools.com/models/screw-press/screw-press.kerf)
- [SVG](https://kerfscript.mylasertools.com/models/screw-press/screw-press.svg)
- [DXF](https://kerfscript.mylasertools.com/models/screw-press/screw-press.dxf)

## Parts

| Part | Quantity | Size |
| --- | ---: | --- |
| Lower platen lamination | 3 | 180 × 140 mm |
| Upper platen lamination | 3 | 180 × 140 mm |
| Knob 1 cover | 2 | 28 × 25.3 mm |
| Knob 1 nut pocket | 2 | 28 × 25.3 mm |
| Knob 2 cover | 2 | 28 × 25.3 mm |
| Knob 2 nut pocket | 2 | 28 × 25.3 mm |
| Knob 3 cover | 2 | 28 × 25.3 mm |
| Knob 3 nut pocket | 2 | 28 × 25.3 mm |
| Knob 4 cover | 2 | 28 × 25.3 mm |
| Knob 4 nut pocket | 2 | 28 × 25.3 mm |

## Settings

| Name | Default | Range or choices |
| --- | --- | --- |
| `width` | `180` | 140 to 260 |
| `depth` | `140` | 110 to 200 |
| `platen_layers` | `3` | 2 to 5 |
| `margin` | `20` | 17 to 28 |
| `rod_height` | `120` | 90 to 180 |
| `opening` | `50` | 15 to 90 |
| `rod_diameter` | `6` | 4 to 8 |
| `thread_pitch` | `1` | 0.7 to 1.5 |
| `nut_flats` | `10` | 7 to 14 |
| `nut_height` | `5` | 3 to 7 |
| `nut_clearance` | `0.25` | 0.1 to 0.5 |
| `washer_height` | `1` | 0.5 to 2 |
| `$thickness` | `3` | 2 to 6 |
| `$kerf` | `0.15` | 0 to 0.3 |

## Source

```kerf
// Screw press: laminated platens and hand knobs with captive hex nuts.
// Clamp the lower platen onto four threaded rods using washers and nuts.
// Glue the knob laminations around measured hex nuts without gluing the
// threads. Put washers beneath the knobs and turn them evenly to press.
// A small craft press for paper and light glue-ups, not for heavy pressing.

/* [Platens] */
width = 180; // [140:5:260]
depth = 140; // [110:5:200]
platen_layers = 3; // [2:1:5]
margin = 20; // [17:1:28]
rod_height = 120; // [90:5:180]
opening = 50; // [15:1:90]

/* [Measured hardware] */
rod_diameter = 6; // [4:1:8]
thread_pitch = 1; // [0.7:0.05:1.5]
nut_flats = 10; // [7:0.5:14]
nut_height = 5; // [3:0.5:7]
nut_clearance = 0.25; // [0.1:0.05:0.5]
washer_height = 1; // [0.5:0.5:2]

/* [Material] */
$thickness = 3; // [2:0.5:6]
$kerf = 0.15; // [0:0.01:0.3]

/* [Hidden] */
$material = "plywood";
t = $thickness;
ph = platen_layers * t;
middle = ceil(nut_height / t);
kh = (middle + 2) * t;
top = ph + opening;
turn = -360 * opening / thread_pitch;
corners = [for (x = [margin, width - margin], y = [margin, depth - margin]) [x, y]];
assert(opening >= 15 && thread_pitch > 0, "Use a positive thread pitch and leave room above the base nuts");
assert(2 * ph + opening + washer_height + kh + 3 < rod_height, "Use longer rods or reduce the opening");
assert(margin > 15, "Keep knobs inside the platen edge");
assert(nut_flats > rod_diameter + 2 && nut_flats < 18, "Measure a suitable hex nut");
assert(width - 2 * margin > 40 && depth - 2 * margin > 35, "Leave a useful pressing area between rods");
module platen() difference() {
  rect([width, depth], r = 7);
  for (p = corners) translate(p) circle(d = rod_diameter + 0.6);
}
module knob() union() {
  circle(r = 11);
  for (a = [0:60:300]) translate([10 * cos(a), 10 * sin(a)]) circle(r = 4);
}
step("Glue up the lower platen and clamp it onto the four rods with nuts") {
  part("Lower platen lamination", stack = platen_layers, at = [0, 0, 0]) platen();
  for (p = corners) {
    hardware("steel", [p[0], p[1], -nut_height], [p[0], p[1], rod_height], rod_diameter, label = "threaded rod");
    for (z = [-nut_height, ph])
      hardware("steel", [p[0], p[1], z], [p[0], p[1], z + nut_height], nut_flats / cos(30), sides = 6, label = "hex nut");
  }
}
step("Glue up the upper platen and drop it over the rods")
  part("Upper platen lamination", stack = platen_layers, at = [0, 0, top]) platen();
step("Glue each knob's layers round a hex nut, without glue on the thread, and screw them down on washers")
  for (k = [0:3]) {
    p = corners[k];
    z = top + ph + washer_height;
    part(str("Knob ", k + 1, " cover"), qty = 2, at = [[p[0], p[1], z], [p[0], p[1], z + (middle + 1) * t]], rotate = [0, 0, turn]) difference() {
      knob(); circle(d = rod_diameter + 0.6);
    }
    part(str("Knob ", k + 1, " nut pocket"), stack = middle, at = [p[0], p[1], z + t], rotate = [0, 0, turn]) difference() {
      knob(); circle(d = (nut_flats + nut_clearance) / cos(30), $fn = 6);
    }
  }
```

Set power, speed and cut order in your laser software. See the [laser software guide](https://kerfscript.mylasertools.com/docs/compatibility/index.md).
