// Pocket Wildlife dragonfly: six legs, big eyes and two pairs of wings in // seven slot-together pieces, on a 150 x 100 mm card. Each pair of wings // drops over a tongue on the thorax. The pieces stay in the card on small // tabs until an adult releases them and sands the nubs. Shapes are drawn at // their finished size and KerfScript moves the cut paths out by half the // beam, so leave kerf offsets off in your laser software. /* [Card] */ // The card, the pieces cut free, or a slot fit test output = "card"; // [card, loose, coupon] /* [Material] */ // Measured thickness of the plywood stock = 3; // [2.8:0.1:3.2] // Width of the laser cut beam = 0.15; // [0.08:0.01:0.25] // Slots are this much wider than the stock fit = 0.08; // [0:0.02:0.18] // Width of the tabs that hold pieces in the card bridge = 0.9; // [0.6:0.1:1.4] /* [Hidden] */ $thickness = stock; $kerf = beam; $fn = 48; $sheet = output == "loose" ? [300, 200] : [160, 110]; card = [150, 100]; s = stock + fit; // Drawn with the thorax 20 mm up, then lowered fy = -6; names = ["Body", "Eyes", "Front legs", "Middle legs", "Back legs", "Forewings", "Hindwings"]; // Piece 0 is the body. Each joint is [piece, place along the body, height, // true when the crosspiece slot opens upward]. The body is notched to match. // The wings, pieces 5 and 6, sit on tongues instead. joints = [[1, 58, 27, false], [2, 36, 20, true], [3, 28, 20, true], [4, 20, 20, true]]; module both() { children(); mirror([1, 0]) children(); } // Rounds the corners of a shape, inside and out module soft(r = 0.8) offset(r = -r) offset(r = 2 * r) offset(r = -r) children(); module slot_up(x, y) translate([x - s / 2, y]) square([s, 200]); module slot_down(x, y) translate([x - s / 2, y - 200]) square([s, 200]); function joint(i) = [for (j = joints) if (j[0] == i) j][0]; module shape(i) { if (i == 0) difference() { body(); for (j = joints) if (j[3]) slot_down(j[1], j[2]); else slot_up(j[1], j[2]); } else if (joint(i) == undef) flat(i); else difference() { cross(i); if (joint(i)[3]) slot_up(0, joint(i)[2]); else slot_down(0, joint(i)[2]); } } // x runs from the tail to the head, y is height above the table. Two // tongues on the thorax carry the wings. module body() translate([0, fy]) union() { path("M50 28 C50 22 46 20 40 20 L18 20 C14 20 11 23 9 26 C-20 28.5 -45 31 -62 32.5 C-66 33 -66 38 -62 38 C-45 38 -20 37 9 36.5 C11 38 13 38 15 38 L45 38 C48 38 50 35 50 32 Z"); translate([58, 31]) circle(r = 9); translate([47, 24]) square([6, 12]); for (x = [16, 31]) translate([x, 37]) square([8, 1 + stock]); } // Crosspieces: x runs across the dragonfly, y is height module cross(i) { if (i == 1) translate([0, fy]) both() { translate([7.5, 34]) circle(r = 7.5); translate([0, 27]) square([3, 12]); } // Legs that reach further out towards the back else let (k = [0, 0, 4, 6, 8][i]) soft(0.6) both() polygon([[0, 25], [5, 25], [10, 23], [10 + k, 28], [13.5 + k, 28], [18 + k, 2], [20.5 + k, 0], [15.5 + k, 0], [10 + k, 23], [9, 18], [6, 11], [0, 11]]); } // Wings lie flat on the thorax: x across the body, y along it, with a slot // over their tongue module flat(i) difference() { scale([0.92, 1]) both() { if (i == 5) path("M0 42 L5 42 C20 43 40 46 58 48 C63 48.5 65 46 63 43.5 C58 39 45 35 30 32 C20 30 10 28 5 28 L0 28 Z"); if (i == 6) path("M0 27 L5 27 C20 27.5 40 27 56 24 C61 23 62 19 58 17.5 C46 14 30 9 16 10 C10 10.5 6 12 5 13 L0 13 Z"); } translate([-s / 2, (i == 5 ? 31 : 16) - fit / 2]) square([s, 8 + fit]); } // Scored rings on the eyes module eyes(i) if (i == 1) translate([0, fy]) both() translate([7.5, 34]) score() for (r = [2.5, 5]) outline() circle(r = r); // Where each piece goes when the model is built: the body stands on edge // along x, crosspieces stand across it and the wings lie on the thorax function placement(i) = i == 0 ? [[0, stock / 2, 0], [90, 0, 0]] : i < 5 ? [[joint(i)[1] - stock / 2, 0, 0], [90, 0, 90]] : [[0, 0, 38 + fy], [0, 0, -90]]; // Where each piece sits on the card [x, y, turn], the tabs that hold it // [x, y, edge direction] in its own coordinates, and the title's box layout = [[79.28, 61.48, 0], [131.28, -13.82, 0], [84.46, 11.48, 0], [115.39, 48.19, 260], [29.44, 21.07, 340], [53.81, 15.58, 350], [56.78, 52.59, 350]]; tabs = [[[17.74, 35.0, 0.0], [16.46, 14.15, 168.8], [64.06, 18.37, -138.0], [-61.99, 32.0, 1.6]], [[7.52, 35.5, -0.1], [-4.5, 21.13, -156.4]], [[-15.53, 28.0, 0.0], [14.8, 19.66, 103.4], [-15.69, 15.92, -103.4]], [[-17.61, 28.0, 0.0], [16.75, 19.88, 103.4], [-17.35, 17.35, -103.4]], [[-19.53, 28.0, 0.0], [18.75, 19.86, 103.4], [-18.88, 19.33, -103.4]], [[54.61, 48.06, -0.8], [-53.24, 40.24, 151.9], [-6.6, 42.16, -4.8]], [[-14.09, 27.17, 0.0], [13.78, 10.1, 173.4], [-42.7, 14.18, 163.7]]]; title = [15.08, 13.88, 34, 13]; // Cut each outline with gaps at the tabs module piece(i, tabs) { difference() { outline() offset(delta = beam / 2) shape(i); for (t = tabs) translate([t[0], t[1]]) rotate(t[2]) square([bridge + beam, 4], center = true); } eyes(i); } if (output == "card") part("Dragonfly card") { rect(card, r = 5); for (i = [0:len(names) - 1]) translate([layout[i][0], layout[i][1]]) rotate(layout[i][2]) piece(i, tabs[i]); engrave() { translate([title[0] + title[2] / 2, title[1] + title[3] * 0.62]) text("DRAGONFLY", size = title[3] * 0.42, halign = "center", valign = "center"); translate([title[0] + title[2] / 2, title[1] + title[3] * 0.16]) text("POCKET WILDLIFE", size = title[3] * 0.15, halign = "center", valign = "center"); } } if (output == "loose") for (i = [0:len(names) - 1]) step(i == 0 ? "Stand the body on edge" : i < 5 ? "Slide the eyes and legs onto the body at their notches" : "Drop each pair of wings over the tongue on the thorax") part(names[i], at = placement(i)[0], rotate = placement(i)[1]) { shape(i); eyes(i); } // Slots from 0.08 mm narrower to 0.12 mm wider than the stock, and three tabs if (output == "coupon") part("Fit coupon") { deltas = [-0.08, -0.04, 0, 0.04, 0.08, 0.12]; difference() { rect([130, 44], r = 3); for (k = [0:5]) translate([12 + k * 21, 26]) square([stock + deltas[k], 20]); } engrave() for (k = [0:5]) translate([12 + k * 21 + stock / 2, 21]) text(str(deltas[k] > 0 ? "+" : "", deltas[k]), size = 2.6, halign = "center", valign = "center"); for (k = [0:2]) translate([22 + k * 43, 9]) difference() { outline() offset(delta = beam / 2) square([24, 8], center = true); for (x = [-12, 12]) translate([x, 0]) square([4, bridge + beam], center = true); } }