// Beam balance: a stable pivoted beam with two level, cord-suspended pans. // Glue the fork uprights into the foot and glue a rim onto each pan. // Fit the beam on a loose pivot bolt, then tie three equal cords per pan. // The tilt control demonstrates motion; it does not calculate equilibrium. /* [Balance] */ arm = 105; // [80:5:145] pivot_height = 165; // [125:5:220] drop = 95; // [65:5:130] pan_diameter = 70; // [50:5:90] base_width = 150; // [120:5:200] base_depth = 100; // [80:5:140] tilt = 7; // [-12:1:12] /* [Material] */ $thickness = 3; // [2:0.5:6] $kerf = 0.15; // [0:0.01:0.3] clearance = 0.15; // [0:0.05:0.4] pin_diameter = 3; // [3:0.5:5] washer_gap = 0.5; // [0.3:0.1:1] /* [Hidden] */ $material = "plywood"; t = $thickness; r = pan_diameter / 2; front = -t / 2 - washer_gap; back = t / 2 + washer_gap + t; assert(abs(tilt) <= 12, "Tilt must stay between -12 and 12 degrees"); assert(pivot_height - arm * sin(12) - drop > 2 * t + 10, "Raise the pivot or shorten the suspension"); assert(arm * cos(12) > r + 22, "Leave room between the pans and the fork"); assert(base_depth > pan_diameter + t + 12, "Widen the foot beneath the pans"); function end(s) = [s * arm * cos(tilt), 0, pivot_height + s * arm * sin(tilt)]; function hanger(s) = end(s) + [0, -t / 2 - 6, 0]; function pan(s) = hanger(s) - [0, 0, drop]; function tie(s, k) = pan(s) + [(r - 6) * cos(120 * k), (r - 6) * sin(120 * k), t]; step("Glue the fork uprights into the foot") { // The foot cuts the slots for the uprights' tabs part("Foot", at = [0, 0, 0], slots = ["Fork upright"], clearance = clearance) rect([base_width, base_depth], center = true, r = 6); part("Fork upright", qty = 2, at = [[0, front, t], [0, back, t]], rotate = [90, 0, 0]) difference() { union() { hull() { translate([-14, 0]) rect([28, 8]); translate([0, pivot_height - t]) circle(r = 12); } translate([-6, -t]) rect([12, t]); } translate([0, pivot_height - t]) circle(d = pin_diameter + 0.3); } } step("Hang the beam on a loose pivot bolt, with a hook at each end") { part("Balance beam", at = [0, t / 2, pivot_height], rotate = [90, -tilt, 0]) difference() { union() { hull() { for (x = [-arm, arm]) translate([x, 0]) circle(r = 9); } hull() { circle(r = 9); translate([0, -14]) circle(r = 10); } } circle(d = pin_diameter + 0.3); for (x = [-arm, arm]) translate([x, 0]) circle(d = 4); } hardware("steel", [0, front - t - 1, pivot_height], [0, back + 1, pivot_height], pin_diameter, label = "pivot bolt"); for (s = [-1, 1]) hardware("steel", hanger(s), end(s) + [0, t / 2 + 1, 0], 3, label = "hook"); } step("Glue a rim on each pan and tie it on with three equal cords") for (s = [-1, 1]) { part(str(s < 0 ? "Left" : "Right", " pan floor"), at = pan(s)) difference() { circle(r = r); for (k = [0:2]) translate([(r - 6) * cos(120 * k), (r - 6) * sin(120 * k)]) circle(d = 2.6); } part(str(s < 0 ? "Left" : "Right", " pan rim"), glue = str(s < 0 ? "Left" : "Right", " pan floor")) difference() { circle(r = r); circle(r = r - 4); } for (k = [0:2]) hardware("cord", hanger(s), tie(s, k), 1.2, sides = 12); }